High-Rise Hotel & Casino Modernization

Section 2.06 H. Car Sills: TP4 Bronze, TP6 Bronze, TP9 Bronze

Elevator Nos. as Scheduled Below: Provide new extruded sills with non-slip surfaces and grooves suitable for guides.

Pit Sump Pumps: Install sump pumps and/or drainage as required by local code authority. Retain existing. TS3-TS4 pump will require replacement.

Section 2.02 MATERIALS: G. Stainless steel: ASTM A167; type 302 or 304. Type 441 is not acceptable.

Provide for elevators as scheduled. Automatically activates during power loss. Supplies power for rescue operation. Causes car to descend smoothly to lowest landing.

Section 2.09 B. Passenger Cars: 4. Car Doors: Finish car side with satin bronze and return finish 1/2 inch around edge of doors.

Elevator Nos. as Scheduled Below: Provide all new door panels at all floors OR where indicated.

Elevator No. ALL: Retain existing oil buffers. Replace seals, clean ram and apply machinist blue dye, readjust to car buffer plates, drain and flush out all oil tanks, clean down, refill and test with full load at contract speed.

Install top of car guard rail complying with OSHA specifications. Must be able to withstand a 200-pound load in any direction, must be 42" – 45" high from floor to top of rail.

Hotel BOH: Modernize elevator nos. BRS1, BRS2, EP1 and EP2 with new MRL gearless machines, new controllers, positioning system, door operators and equipment, hall door equipment, signals and fixtures, hoistway wiring, cab components and recondition other equipment as specified.

Hotel Tower 1: Modernize elevator nos. TP1-TP6 with new controls, new gearless machines, positioning system, door operators and equipment, governor, signals and fixtures, hoistway wiring, cab interiors, and recondition other equipment as specified.

Restaurant Kitchens: Modernize elevator nos. KS2, KS3, KS4, KS5, KS7 with new controls, new pumping units, positioning system, door operators and equipment, signals and fixtures, hoistway wiring, cab components, and recondition other equipment as specified.

For traction machines, employ a Structural Engineer to study the machine room floor and wall support. Any machines beams can be added.

Motor Drive Units: Provide New, Regenerative

Freight Elevators BRF1, FE3, FE4: Provide new door motors.

Provide add for one (1) new 15 inch Elite Display in each cab. Provide a USB port in the service cabinet for content load up. Provide for elevators TP1-TP10, CTP1, CP1-CP2, WG1-WG2, EPP1-EPP4, WPP1- WPP4.

Corporate Center #1-4: Provide add for one (1) new 12.1 inch Elite Display in each cab. Provide a USB port in the service cabinet for content load up.

Elevator No. ALL: Provide separate lights mounted above drop ceiling. The unit shall have sufficient capacity to keep the lights in continuous operation for four hours and the alarm bell for one hour.

Provide a complete Voice Annunciation Unit (including the Device, the Wiring to the elevator cab, Speaker and Control System Software designed to include a Voice Annunciation Interface).

Communication circuit: Telephone circuit terminated at junction box of each controller.

Governor Ropes: Provide New

Elevator No. ALL: Provide new heavy-duty master type solid state closed loop door operators mounted on car enclosure utilizing minimum 12-guage support angles to isolate from direct mounting of operator on the car top.

Section 2.07 L. Hall Faceplates: TP1 Satin Bronze, TP2 Satin Bronze, TP3 Satin Bronze, TP4 Satin Bronze, TP5 Satin Bronze, TP6 Satin Bronze, TP7 Satin Bronze, TP8 Satin Bronze, TP9 Satin Bronze, TP10 Satin Bronze, CP1 Satin Bronze, CP2 Satin Bronze

Car Operating Panels: Provide New

Car Position Indicators: Provide New Hall Position Indicators: Provide New

Communications: Provide New